Camera issues：

Camera installation：

1.Front-view camera installation:
- Connect the power cable of the front-view camera to the red ACC cable on the ISUDAR module harness. Connect the video output cable of the front-view camera to the Front-CVBS cable on the ISUDAR module harness. Successful connection will be visible in the DVR app on the ISUDAR module page.

2.Rear-view camera installation:

--Automatic transmission car:

1.Original rear view camera：No manual wiring is required, the rearview camera will work normally after the module is installed.

2.Aftermarket rear view camera: Manual wiring is required. The output plug of the camera extension cable is connected to the REAR CVBS, and the trigger cable is connected to CAM-12V. The trigger cable at the other end is connected to the red cable, and the black cable is grounded. (As shown in the picture)

Note: ISUDAR module currently only supports rear-view cameras with a maximum resolution of 720P

--Manual transmission car:

1.Original rear view camera：Manual wiring is required. Connect the reverse control cable (Reveres) to the positive terminal of the reversing light.

Except for the following two products:
-For SEMG (the black module)
Turn on the number 2 in the digital switch of the box

2.Aftermarket rear view camera: Manual wiring is required. The output plug of the camera extension cable is connected to the REAR CVBS, and the trigger cable is connected to the REVERSE. The other end of the trigger cable is connected to the red cable and connected to the positive pole of the reversing light, and the black cable is grounded. (As shown in the figure)

Note: ISUDAR module currently only supports rear-view cameras with a maximum resolution of 720P

Camera display:

1. Factory front-view camera:
- Cannot be displayed independently; the module can only switch to the front-view image after shifting out of reverse (based on ISUDAR module settings), displaying for a maximum of 10 seconds.
2. Aftermarket front-view camera:
- View via the DVR app on the ISUDAR module's home screen.

3. Factory rear-view camera:
- Configure the following settings on the ISUDAR module page:
Aftermarket Camera | Original Camera: ON
Rear Camera | 360 Panoramic: OFF
Note: Even if the vehicle lacks a factory rear-view camera and is equipped only with parking sensors, these settings must still be selected.
4. Aftermarket rear-view camera:
- Configure the following settings on the ISUDAR module page:
Aftermarket Camera | Original Camera: OFF
Rear Camera | 360 Panoramic: OFF
Note: When using an aftermarket camera, the factory parking sensor display will appear in the top-right corner of the reversing screen.

Camera issues：

Camera installation：

1.Front-view camera installation:
- Connect the power cable of the front-view camera to the red ACC cable on the ISUDAR module harness. Connect the video output cable of the front-view camera to the Front-CVBS cable on the ISUDAR module harness. Successful connection will be visible in the DVR app on the ISUDAR module page.

2.Rear-view camera installation:

--Automatic transmission car:

1.Original rear view camera：No manual wiring is required, the rearview camera will work normally after the module is installed.

2.Aftermarket rear view camera: Manual wiring is required. The output plug of the camera extension cable is connected to the REAR CVBS, and the trigger cable is connected to CAM-12V. The trigger cable at the other end is connected to the red cable, and the black cable is grounded. (As shown in the picture)

Note: ISUDAR module currently only supports rear-view cameras with a maximum resolution of 720P

--Manual transmission car:

1.Original rear view camera：Manual wiring is required. Connect the reverse control cable (Reveres) to the positive terminal of the reversing light.

Except for the following two products:
-For SEMG (the black module)
Turn on the number 2 in the digital switch of the box

2.Aftermarket rear view camera: Manual wiring is required. The output plug of the camera extension cable is connected to the REAR CVBS, and the trigger cable is connected to the REVERSE. The other end of the trigger cable is connected to the red cable and connected to the positive pole of the reversing light, and the black cable is grounded. (As shown in the figure)

Note: ISUDAR module currently only supports rear-view cameras with a maximum resolution of 720P

Camera display:

1. Factory front-view camera:
- Cannot be displayed independently; the module can only switch to the front-view image after shifting out of reverse (based on ISUDAR module settings), displaying for a maximum of 10 seconds.
2. Aftermarket front-view camera:
- View via the DVR app on the ISUDAR module's home screen.

3. Factory rear-view camera:
- Configure the following settings on the ISUDAR module page:
Aftermarket Camera | Original Camera: ON
Rear Camera | 360 Panoramic: OFF
Note: Even if the vehicle lacks a factory rear-view camera and is equipped only with parking sensors, these settings must still be selected.
4. Aftermarket rear-view camera:
- Configure the following settings on the ISUDAR module page:
Aftermarket Camera | Original Camera: OFF
Rear Camera | 360 Panoramic: OFF
Note: When using an aftermarket camera, the factory parking sensor display will appear in the top-right corner of the reversing screen.